Powermate CHFN35P Use and Care Manual download pdf (Page 4)

2- ENG LISH

FOR YOUR MODELS. Do not use the wrong fasteners or

load the fasteners incorrectly.

• CHECK FOR MISALIGNMENT OR BINDING OF

MOVING PARTS, BREAKAGE OF PARTS, AND ANY

OTHER CONDITION THAT MAY AFFECT THE TOOL'S

OPERATION. If damaged, have the tool serviced before

using. Many accidents are caused by poorly maintained

tools.

• CHECK SAFETY BEFORE USE. Make sure the safety

operates properly. Never use the tool unless the safety

is operating properly, otherwise the tool could drive a

fastener unexpectedly. Do not tamper with or remove the

safety, otherwise the safety becomes inoperable.

• DO NOT USE TOOL IF TRIGGER DOES NOT ACTUATE

PROPERLY. Any tool that cannot be controlled with the

trigger is dangerous and must be repaired.

• NEVER USE TOOL WHICH IS DEFECTIVE OR

OPERATING ABNORMALLY. If the tool appears to be

operating unusually, making strange noises, or otherwise

appears defective, stop using it immediately and arrange

for repairs by an authorized service center.

• MAINTAIN TOOLS WITH CARE. Keep the tool clean and

lubricated for better and safer performance.

• NEVER CARRY THE TOOL BY AIR HOSE.

• STORE TOOLS OUT OF THE REACH OF CHILDREN AND

OTHER UNTRAINED PEOPLE. Tools are dangerous in

the hands of untrained users.

• PLACE TOOL PROPERLY ON WORKPIECE. Do not drive

fasteners on top of other fasteners or with the tool at too

steep of an angle; the fasteners can ricochet and hurt

someone.

• DO NOT USE THE TOOL AS A HAMMER.

• KEEP ALL SCREWS AND COVERS TIGHTLY IN PLACE.

• KEEP FACE, HANDS AND FEET AWAY FROM FIRING

HEAD AT ALL TIMES. Never place your face, hands or

feet near the ﬁring head.

• DO NOT DISCONNECT AIR HOSE FROM TOOL

WITH FINGER ON TRIGGER. The tool can ﬁre when

reconnected to an air supply.

• DO NOT LOAD FASTENERS WITH TRIGGER PULLED

OR SAFETY DEPRESSED.

• NEVER PLACE A HAND OR ANY PART OF BODY IN

FASTENER DISCHARGE AREA OF TOOL.

• DO NOT DRIVE FASTENERS INTO THIN BOARDS OR

NEAR CORNERS AND EDGES OF WORKPIECE. The

fasteners can be driven or a way from the workpiece hit

someone.

• DISCONNECT AIR HOSE FROM TOOL WHEN:

1). Doing maintenance and inspection;

2). Turning the adjuster and top cover;

3). Attaching or removing the no-mar tip;

4). Clearing a jam;

5). It is not in use;

6). Leaving work area;

7). Moving it to another location;

8). Handing it to another person.

Never attempt to clear a jam or repair the tool unless you

have disconnected air hose from the tool and removed all

remaining fasteners from the tool. The tool should never

be left unattended since people who are not familiar with

the tool might handle it and injure themselves.

TOOL SERVICE

• USE ONLY ACCESSORIES THAT ARE IDENTIFIED

BY THE MANUFACTURER FOR THE SPECIFIC TOOL

MODEL.

• USE OF UNAUTHORIZED PARTS OR FAILURE TO

FOLLOW MAINTENANCE INSTRUCTIONS MAY

CREATE A RISK OF INJURY.

• USE ONLY THE LUBRICANTS SUPPLIED WITH THE

TOOL OR SPECIFIED BY THE MANUFACTURE.

• TOOL SERVICE MUST BE PERFORMED ONLY BY

QUALIFIED REPAIR PERSONNEL.

AIR SOURCE

• NEVER USE OXYGEN OR OTHER BOTTLED GASES AS

A POWER SOURCE. Explosion may occur. Combustible

gases and other bottled gases are dangerous and may

cause the tool to explode.

• DO NOT EXCEED MAXIMUM RECOMMENDED AIR

PRESSURE MARKED ON THE TOOL. Use only clean,

dry, regulated, compressed air within the rated pressure

range marked on the tool. Never connect the tool to

pressure as which potentially exceeds 200PSI the tool

can burst.

• DO NOT ABUSE THE AIR HOSE. Protect all hoses from

kinks, restrictions, solvents or sharp objects. Keep air

hose away from heat, oil, sharp edges or moving parts.

Replace damaged hoses immediately. Damaged hoses

can burst or whip around.

• CHECK ALL FITTINGS, HOSES, PIPES, CONNECTIONS

AND COMPRESSOR BEFORE EACH USE OF THIS

TOOL. Repair or replace damaged or leaking hoses

and connections immediately. Damage to a hose or

connection can cause a pressure hose to break and

whip around the work area, and can lead to injury.

1 2 3 4 5 6 7 8 9 ... 39 40

Comments to this Manuals

No comments

Powermate CHFN35P Use and Care Manual Page 4

Comments to this Manuals

Related products and manuals for Nail Gun Powermate CHFN35P